PreFormed ProPan Ready to Tile Shower Pan 36 x 60 PVC Drain Made in USA

Description: Preformed ProPan Ready to Tile Shower floor kit36" x 60" Center Drain PVC (also available ABS) ProPan Shower Pans are made from high-density polystyrene with a liquid-applied waterproof coating that creates a code-required slope. ProPan Shower Bases have the proper slope and drain assembly built-in. With ProPan, contractors have the ability to modify pans on the job site. PVC or ABS Drain availableOther sizes include Custom pan available In stock - Ship Same Day Pan Base Kit Include: • 1 ProPan Base • 1 Preformed Solid Curb • 1 Ebbe Square Drain (color of your choice)• 1 Polyurethane Sealant Our shower pans include the Ebbe Square Drain with Ebbe Hair Trap Custom Made - Floor Kit with drain and curb - $0.40 per sq Inch Pro Pan™ is a professional grade shower pan that offers contractors the ability to modify, cut or even extend a shower pan on-site for unlimited residential and commercial applications. ProPan™ is lightweight, completely waterproof and easy to install. Propan™ is designed to be used with ProPanel™ waterproof backerboard for a complete waterproof installation and system warranty. Use any Modify thin-set setting material for installation ProPan™ adheres to industry standards with a 1/4" per foot slope to the drain and come standard with an integrated drain assembly cemented into the base. Every ProPan™ comes standard with the Ebbe square drain and grate assembly. ProPan™ can be cut down in size easily with a circular saw. The prefabricated 1/2" notch can be cut back into the pan base for proper installation of 1/2" ProPanel™ Backer Board. ProPan™ can also be extended with the ProPan™ 2'x4' extensions. ProPan is a professional grade shower pan that offers contractors the ability to modify, cut or even extend a shower pan on-site for unlimited residential and commercial applications. ProPan is lightweight, completely waterproof and easy to install. ProPan is available in 4' x 4' and 3' x 5' standard sizes. The 4' x 4' pan is centered drain located while the 3' x 5' pan drain is located at 18" and 6' for most tub replacement installations. Every ProPan comes with a curb attachment for those requiring a curb entry. ProPan is made of high-density polystyrene insulation and reinforced with fiberglass mesh. It is engineered using a polymer cement coating that offers both 100% waterproof protection and added strength. The ProPan has met a residential and light-commercial rating in the demanding Robinson-Floor test.The material used to construct our PreFormed Shower Pan is 100% waterproof, and is rot resistant. This Pro Pan Shower Pan base available with any of our Ebbe Square Shower Drain with no extra charge, just specify which finish grade color you want Easy, Waterproof, Worry Free. The difference is CLEAR. The "Anywhere" Solution FEATURES: - Waterproof and rot resistant - Light weight, easy to handle and install - Time and labor savings - Can be installed and tiled in the same day - Drain assembly and curb included - No special training necessary - Custom sizes can be ordered - Sloped per industry standards - listed by UPS/IAPMO to meet UPS PS 106-2010 Made in the U.S.A USA SELLER - In stock - Ship Same Day Excluding - Alaska, Hawaii, and Puerto Rico 30 Days money back guarantee INSTALLATION Prepatory Work (without wall board) • Ensure that walls are square and plumb. • Cut and install 2 stacked 2 x 4’s between studs on the floor to provide support to backer board. • Sub floor under pan must be clean and level. Cut out a 5” diameter hole around drainpipe to allow pan to be inserted into floor. • Cut floor drainpipe 1 3/8” (35 mm) below floor level. • Remove square strainer from the drain and test fit pan to make certain if fits over drainpipe and sits flush and level with the floor. • Remove the pan. • If the pan needs to be site adjusted to fit the shower use a circular saw or utility knife to cut the pan to the proper shower dimensions. • Dry fit the pan to make certain it properly fits over the drainpipe and sits flush and level with the floor. • Using a circular saw with guide or utility knife recut the rabbet joints into the edges of the pan where required. For PRO-500-503 models the rabbet joint should be 1/2” (12 mm) deep and 1/2” (12mm) in from the edge of pan. For PRO-504 rabbet joint should be 7/8” (22 mm) deep and 1/2” (12 mm) in from edge of pan. Installation • Apply a medium bed, modified thinset to the floor area and underside of pan using a 1/4” x 1/4” (6 mm x 6 mm) notched trowel. • Apply a liberal coat of PVC or ABS cleaner and solvent cement to the drainpipe and inside the drain where the connection will be made. (If plumber is making the connection this step can be performed after the pan is set into thinset). Note: Follow manufacturer’s instructions. • Set pan into the wet thinset and apply pressure to achieve complete coverage, insuring that the drain pipe and waste line are properly connected. Check pan for level set on floor. Apply weight (thinset bags) equally across pan for 30 minutes Wall Backer Board Installation ProPanel Lightweight Waterproof Backer Board • Apply a 1/2” (12 mm) continuous thick bead of polyurethane sealant into the rabbet joint of the ProPan. • Using 1/2” (12 mm) ProPanel, set the board into the sealant until you see sealant oozing out along the joint. Spread excess sealant ensuring a continuous seal at the joint. • Fasten ProPanel directly to framing with ProPanel fasteners starting 1’ (300 mm) above the shower pan. Whenever two boards come together to make a joint, apply a 1/2” (12 mm) bead of sealant on board edges. All boards must be fitted together tightly allowing sealant to ooze from joint. Spread excess sealant ensuring a continuous seal at joint. • All fasteners must be completely covered with sealant and spread to form a seal. Concrete Backer Board or Other Backer Board • Apply a 1/2” (12 mm) continuous thick bead of polyurethane sealant into the rabbet joint of the ProPan. • Using 1/2” (12 mm) cement backer board, set the board into the sealant until you see sealant oozing out along the joint. Spread excess sealant ensuring a continuous seal at the joint. Take care when installing board onto base of ProPan. • Fasten Cement Backer Board per manufacturer’s installation instructions directly to framing with cement backer board screws starting 1’ (300 mm) above the shower pan. Follow the instructions manufacturer’s instructions for treating seams. • All screw heads should be covered with thinset. After Wall Backer Board is installed • Determine location of ProPan Curb. Affix curb to floor by applying a 1/4” (6 mm) modified mortar bed to floor and underside of curb. Before setting curb in place, apply a 1/2” (12 mm) bead of sealant to ProPan rabbet channel and to the adjoining wall panels. • Next, screw strainer down to correct height to match tile. If required, cut threads down to adjust strainer to correct height. Always ensure a minimum of 1” (25.4 mm) of threads remain on strainer. Pack thinset or pea gravel into area cut out for strainer adjustment. After ProPan Installation is Complete ProPanel Lightweight Waterproof Backer Board • Apply another 1/2” (12 mm) bead of sealant on all ProPan perimeter joints and curb to fill any voids in sealant. Concrete Backer Board or Other Backer Board • Apply 6” (152 mm) fiberglass mesh at shower pan base, 3” (76 mm) on pan base and 3” (76 mm) up wall. Apply two coats of liquid waterproofing over fiberglass mesh and up the walls a minimum of 1’ (300 mm). Allow 1st coat of waterproofing to cure completely before applying the 2nd coat. Tile Installation Detail • Install tile using a modified thinset and in accordance with the Tile Council of North America(TCNA) guidelines. Prepatory Work (with wall board already in place) • Ensure that walls are square and plumb. • Sub floor under pan must be clean and level. Cut out a 5” diameter hole around drainpipe to allow pan to be inserted into floor. • Cut floor drainpipe 13/8” (35 mm) below floor level. • Remove square strainer from the drain and test fit pan to make certain if fits over drainpipe and sits flush and level with the floor. • Remove the pan. • If ProPan needs to be site adjusted to fit, use a circular saw or utility knife to cut the pan to the proper dimensions. • Do not cut rabbet channel back into pan base. • Dry fit the pan to make certain it properly fits over the drainpipe and sits flush and level with the floor. Installation • Apply a medium bed, modified thinset to the floor area and underside of pan using a 1/4” x 1/4” (6 mm x 6 mm) notched trowel. • Apply a liberal coat of PVC or ABS cleaner and solvent cement to the drainpipe and inside the drain where the connection will be made. (If plumber is making the connection this step can be performed after the pan is set into thinset). Note: Solvent choice based on drain type. • Set pan into the wet thinset and apply pressure to achieve complete coverage, insuring that the drain pipe and waste line are properly connected. Check pan for level set on floor. Apply weight (thinset bags) equally across pan for 30 minutes. • Determine location of ProPan Curb. Affix curb to floor by applying a 1/4” (6 mm) modified mortar bed to floor and underside of curb. Before setting curb in place, apply a 1/2” (12 mm) bead of sealant to ProPan rabbet channel and to the adjoining wall panels. • If the original rabbet joints remain on the perimeter fill them with a medium bed modified mortar. • Next, screw strainer down to correct height to match tile. If required, cut threads down to adjust strainer to correct height. Always ensure a minimum of 1” (25.4 mm) of threads remain on strainer. Pack thinset or pea gravel into area cut out for strainer adjustment. After ProPan Installation is Complete ProPanel Lightweight Waterproof Backer Board • Apply a 1/2” (12 mm) bead of sealant on all ProPan perimeter joints and curb ensuring a continuous bead of sealant. Concrete Backer Board or Other Backer Board • Apply 6” (152 mm) fiberglass mesh at shower pan base, 3” (76 mm) on pan base and 3” (76 mm) up wall. Apply two coats of liquid waterproofing over fiberglass mesh and up the walls a minimum of 1’ (300 mm). Allow 1St coat of waterproofing to cure completely before applying the 2nd coat. Tile Installation Detail • Install tile using a modified thinset and in accordance with the Tile Council of North America (TCNA) guidelinesOur store open to the public / Buy here pick up at our store Mon - Fri 7:00 am - 5:00pm Sunday 8:00am - 12:00pmQuestions? Contact us at 877 880 8453 or email us 30 Days money back guaranteeVisit our store at https://stores.ebay.com/FlooringSupplyShop

Price: 949 USD

Location: Los Angeles, California

End Time: 2024-09-25T03:39:19.000Z

Shipping Cost: 295 USD